How To Unclog A Sink The DIY Way

A clogged sink is a trivia issue that can cause big problems. If it’s your kitchen sink, you might be dealing with dirty dishes that are piling up or having a difficult time with after dinner cleanup. There are many easy methods to clear a clogged sink before you decide to call a plumber. Chances are that you will save a lot of money by fixing this minor issue yourself. You might be able to save yourself the additional expense by taking DIY route and using simple methods that work. If you’re a person who prefers to avoid using chemicals in your home, this list is perfect for you.

clogged sinkYou might be inclined to seek professional help on how to unclog a sink. Before you do, consider trying all of the processes below. You don’t have to be tech savvy to take care of a blocked drain. It is likely clogged with soap scum and hair. In the case of a kitchen sink, it could be food causing the problem. Try the obvious. If your kitchen sink is clogged, turn on the disposal and see if this drains the standing water in the sink.

To start, lift out the stopper from your sink. If you’re dealing with a bathroom sink or tub drain, the stopper may be attached to the sink itself. If this is the case, you can pull out the stopper by removing the pivot rod that keeps it attached to the sink. You may need to equip yourself with slip joint pliers to pull out the pivot rod and stopper.

Hot water

It may seem like water is the issue and not the solution. However, hot water can clear up the problem relatively quickly. First, remove any standing water from the sink using a small cup or something similar. Pour boiling hot water down the drain. You can follow this up by pouring a half cup of salt down the drain followed by more water. You can use regular table salt for this. The hot water should “melt” the substance that is clogging your drain. If the sink does not begin to drain, remove the standing water and repeat the process.

Baking soda and vinegar

Another method of clearing your clogged drain uses baking soda and vinegar. Start by pouring baking soda down the drain and following it with white or apple cider vinegar. The mixture will begin to bubble. Once the bubbles subside, you can place the stopper in the sink and wait for about 15 minutes.

Baking soda and salt

Mix a cup of baking soda with a half cup of salt. Pour this mixture into the sink. Remove any standing water that may be present first. You’ll probably need to allow the mixture to sit there for seven or eight hours. Finish the process and ensure the clog has been cleared by pouring boiling water down the drain. The combination of a half cup of baking soda and a half cup of warm vinegar will help prevent clogs from happening in the future. This will also eliminate any odors and keep your sink smelling decent.


Sometimes a good old fashioned plunging is what your sink needs. Add enough water to cover up the bell of the plunger when it is in the sink. Plunge vigorously until you hear or feel the clog clear.

Auger or plumber’s snake

You can use a plumber’s snake to remove. This is a great way to remove items stuck deeper within the drain. Place the snake apparatus as far within the drain as you can, wiggle it around to catch debris and begin pulling up the snake. You know this method has worked well when you pull up the snake and see particles all over the snake.

A basic coat hanger will also do the trick when it comes to clearing a clogged drain. Untwist a wire hanger and make it as straight as possible. Use this to fish out anything that may be clogging the drain. The wire hanger will not reach as far into the drain as a plumber’s snake but you should be able to clear at least some of the clog. There are lots of effective tricks for getting gunk out of your drain cheaply and quickly. No more water pooling in the sink or under your feet in the shower.

What To Do When Your Hot Water Heater Breaks Down

We’ve all been there -you turn on the shower to take a bath only to realize you don’t have hot water. This can be a confusing moment for most home owners who don’t know the next step to take. While you can always call the nearest technician, you still have to wait until they get there to get your hot water heater working. Luckily, there are a few steps you can take to try remedy the situation.

Problem with electrical heaters can cause a number of symptoms including temperature issues, noise, leaks, discoloration and even odor. Such problems can be caused by a wide range of reasons but most of them revolve around age and usage. Here are some of the most common causes;

  • Leaks – Over heating, faulty pressure and temperature valve, loose bolts or leaking water tank.
  • Temperature – Faulty heating elements or thermostat.
  • Noise – Overheating caused by build up of sediments
  • Discoloration or Odor – Corrosion or decaying sacrificial anode rod

Depending on your unit model, there are various techniques you can use to remedy all of these issues. Some of these tasks are not DIY friendly while others are fairly easy to get around. Before taking on a task, make sure you have the right tools for the job as well as proper knowledge of the process.

When you notice a problem with your hot water heater, make sure you take action early. Ignoring any change in the way your unit operates could lead to expensive repairs in the near future. This is especially awful when the problem could have been fixed with a simple tuneup.

Components in all electrical devices wear off after a while of use. This is regardless of whether you took care of it well or not. When your your hot water heater starts acting up, the first thing you should do is troubleshoot it for problems. In most cases, you simply need to replace some components to get it back running properly. Some other times, you’ll need a professional to look into the issue.

With proper maintenance, your water heater should serve you for an extended period of time. However, most hot water heaters have a lifespan of 10 to 15 years. If you are using an old water heater, then replacing it with a new one might be a better idea.

How to Repair your Hot Water Heater

The first thing you need to do when your hot water heater stops working is check to see which elements need to be replaced with new ones. But before you do this, check to see whether the circuit breaker is on or tripped.

If the heating elements are all in good working condition, then the problem could lie with the cutoff switch or thermostat. Testing to see whether the thermostat or cutoff switch is working can be complicated. But since they are not that expensive, you might as well just buy new ones.

Safety is important when dealing with electricity. Make sure you turn off your water heater from the main electrical panel before you start troubleshooting.

Different water heater models will require different techniques to check and replace worn out or faulty elements. Make sure you read the instruction manual on how to perform these tasks or check online for information on the model you have.

When it’s Time to Call a Technician

As mentioned earlier, it would be better to replace your water heater if it has reached its limit or nearing it. Newer models are more energy efficient and are easier to both maintain and repair. When shopping for a new water heater, familiarize yourself with terms search as Seasonal Energy Efficiency Ratio (SEER Rating). This is what the heating industry uses to show how energy efficient a unit is when you are buying. It will cost you more to buy a higher rated unit but pay off in the long run.

Your maintenance guy should know what ails your unit with ease. If you’ve been performing regular maintenance services on your unit, then whatever is interfering with your unit’s proper operation shouldn’t be difficult or costly to fix. However, you do require a professional to properly fixed your hot water heater.

When it comes to selecting a heating technician, you want to go for a licensed and experienced company or individual. Never gamble when it comes to choosing such a service. Mistakes can be costly when it comes to hiring any heating technician. Carry out a research on available options or get recommendations from those close to you. If you go that extra mile and check reviews on different service providers, then you’ll be a step closer to getting a reliable service.